POLISHER 1200W WOOL BONNET 180MM WITH 4M CORD 6 MONTHS WARRANTY
![](images/torkcraft/powertools/pol02_sm1.jpg)
Wattage: 1200W
No load speed: 1100-3500 RPM
Supplied with a ø180mm wool bonnet buff and backing pad.
Application:
The polisher is a power tool used in the finishing process, used with polishing buffs and compound sponges to yield a dramatic difference on a painted surface.
The objective of polishing is to remove imperfections in the clear-coat that
cause the paint to look dull. Surface imperfections can include swirls,
scratches, water spots, etchings, industrial fallout, oxidation, etc.
Features:
- Professionally manufactured for the automotive paint care and detailing industries.
- Ergonomically designed to reduce fatigue in long term use.
- The polisher has various hand-held positions to better hold the polisher at angles.
- Gear system has a two-level deduction. With two times the amount of torque than a single gear set polisher.
The polisher range:
ORDER NO. | DESCRIPTION | WARRANTY |
POL01 | Polisher, 800W. Supplied with ø125mm wool buff | 6 Months |
POL02 | Polisher, 1200W. Supplied with ø180mm wool buff | 6 Months |
POL03 | Polisher, 1700W. Supplied with ø180mm sponge pad | 6 Months |
The Tork Craft polisher features a built-in variable speed control. It is advisable to use the polisher on it's lowest speed to prevent friction. Lift the polisher often away from the panel (under no-load) to allow the motor to cool down.
Spare parts for the POL02 polisher:
ORDER NO. | DESCRIPTION |
POL02-12 | Big gear |
POL02-13 | Bearing |
POL02-16 | Aluminium head |
POL02-19 | Fixation knob |
POL02-24 | Armature |
POL02-29 | Field coil (stator) |
POL02-30 | Motor housing |
POL02-33 | Carbon brushes |
POL02-37-38 | Speed control (switch) |
POL02-40 | Rear handle |
POL02-46 | Trigger switch |
![](images/icons/manualsdownload_header.png)
Steps to take when polishing a panel:
1. Preparing the panel:
- Sometimes a panel has fine over-spray left from spraying the clear-coat. This needs to be removed by lightly sanding with a fine abrasive paper. All over-spray need to be sanded out up to P1500 grit.
- The panel should be washed when all spray-finishing defects have been removed. Any dirt particles could cause scratch marks when polishing.
- Tight curves and ends of the panel should be masked-off to prevent the effects caused by point pressure. The polisher should always be used on flat surfaces.
2. Applying the polishing compound:
- A five rand coin amount of polishing compound should be applied to the buff. Switch the polisher to it's lowest speed setting.
- Switch on the polisher and gradually spread the polishing compound over the panel.
- Keep moving the polisher on the panel to have as little amount of pressure and friction.
- The polishing compound will remove the scratch marks caused by the P1500 sand paper and it will bring out an impressive gloss finish.
- Remove the masking from the panels and apply the polishing compound to a microfiber cloth. Hand polish (by moving your hand in a small circular motion) the tight curves and ends in the panels until the same finish is achieved as from the polisher.
3. Wash the panel when finished:
- Wash the panel after polishing to remove any residue from the polishing compound.
consider safety for your health and the people around you | |||
General safety suggestions:It is advisable to always have the following items nearby and in a good condition
|
|||
![]() |
![]() |
![]() |
![]() |
Wear Gloves
|
Eye Protection
|
Hearing Protection
|
Dust Mask
|